This will verify that the interconnect is working. On releasing the button the local Alarm will stop sounding immediately and the remote Alarms will stop sounding approximately 3 seconds later. The red light on the first unit only will flash about once a second. All the units should alarm within 10 seconds of the first horn sounding. Interconnected Alarms only – Test the first unit by pressing the button for 10 seconds.Check for any sign of contamination such as cobwebs or dust and clean the alarm as described in the “CLEANING YOUR ALARM” section, if necessary.We do not recommend testing with smoke or heat as the results can be misleading unless special apparatus is used. This can set fire to the Alarm and damage the house Pressing the test button simulates the effect of smoke or heat during a real fire and is the best way to ensure the Alarm is operating correctly. The alarm will stop when the button is released. A red light on the cover, will flash while horn is sounding. (Press the test button for up to 10 seconds to ensure the sensor chamber, electronics and sounder are working. After 24 hours the memory will be cleared. If the memory has been set indicating that the Alarm has been activated in the last 24 hours, the red light will flash twice every 40 seconds. (Check that the green mains indicator light is on.(If it is off check circuit breakers, fuses and wiring etc.) Check that the red led on the cover flashes once every 40 seconds to indicate normal operation. TESTING & MAINTAINING YOUR ALARMĬheck all your alarms weekly, especially after initial installation or after re-occupation (e.g. We recommend that the battery is replaced at least every three years for optimum performance. Reinstate mains power to alarm (green light on cover should come on).Press and hold the test button – horn should sound loudly.(The unit cannot be replaced on the base unless a battery is installed). A click should be heard as the alarm engages. Older batteries will give beeps prematurely. We recommend that the “use by date” on the battery should still have at least 2 years to go. Use only 9V Alkaline batteries Duracell MN1604, Energizer 522. Connect new battery by clipping back on to battery snap connectors.Unclip battery from battery snap connectors.Locate battery slot in base of alarm as shown below.Remove unit as shown in “ALARM REMOVAL” section on page 2.Switch off mains power to alarm (green light on cover should go out).If your alarm sounds for no reason and will not reset, it can be removed by releasing the clip on the base. Do not open or insert anything into the alarm. Your alarm is a mains 230V AC electrical appliance.Do not allow paint, water or dust to contaminate your alarm. Remove or completely cover your alarm when decorating to prevent dust or other contamination damaging the unit.This will reduce the risk of false alarms. If a nuisance alarm occurs, press the test/hush button to silence the alarm for 10 minutes. If alarm beeps once every 40 seconds for over 20 minutes, the battery is probably depleted (models Ei141RC/144RC/146RC only) and must be replaced.All the other interconnected alarms should sound. The alarm will sound loudly and the red light on the cover should flash rapidly. Test weekly – press and hold the test button on the alarm for 10 seconds.Regularly check that the green mains indicator light on the cover is lit.This is indicated by 2 red led flashes every 40 seconds for 24 hours (after the event). The memory feature allows an Alarm that has previously activated to be easily identified. This will check the sounder, battery voltage and internal circuitry. The large Test and Hush button allows the user to check the operation of the Alarm. If it is depleted it will give a short beep every 40 seconds. The Alarm automatically monitors the battery every 40 seconds. The Ei161e may operate as a standalone Alarm or may be interconnected via hardwire or wirelessly with the RadioLINK + module Ei100MRF (sold separately) to communicate with compatible Ei Alarms and accessories. The Easi-fit base automatically connects both mains power and battery as the detector head slides on. The Alarm is supplied with the " Easi-fit" base to facilitate quick and simple installation, combined with easy detector head removal and replacement. Powered by 230V AC with a rechargeable 10 year built in battery backup supply to ensure continuous operation (up to 4 months) in the event of a power failure. The Ei161e Ionisation Smoke Alarm is fitted with a proprietary sensor to quickly sense high energy smoke particles from fast flaming fires. This product is End of Life - Replace with Ei3024
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |